by subpixel, subpixels.com
A small application made with Processing to produce MIDI control messages from a live audio feed. Auto-levelling frequency band meters are used to obtain "peak" output values across the entire audio spectrum analysed (whereas it is usual to have strong bass response with weaker treble response), and easing is applied to make the levels less erratic.
The auto-levelling algorithm tracks high and low values output by the audio analysis (FFT) for each frequency band:
10 separate monitor outputs are supplied, where each monitor is attached to one of the frequency band meters and that meter's output is scaled to the particular output range for the monitor, allowing for a reduced final output range as well as inverted ranges. Controls are provided to select the MIDI output device and the MIDI channel to use, as well as for selecting which monitors are connected to which meters and the monitor output ranges.
This app has been used to control VJ applications Resolume and Neon v2, allowing simultaneous control from an external MIDI controller on the same channel (using loopMIDI as a virtual MIDI driver and MIDI-OX for routing).
The "Stereo Mix" device has been removed from Windows 10. To do monitoring in Windows 10 now requires a hacky workaround using a 3rd party driver. See How to Get Stereo Mix in Windows 10.
This app, as of v11, searches for a mixer name starting with "CABLE Output", which is for the VB-CABLE Virtual Audio Device from VB-AUdio Software. If you are using a different virtual audio device, you will need to edit the source and rebuild the app yourself.
spxlAudioToMidi v11.1 (2020-10-10): developed and tested with Processing v3 (3.5.4 Win 64) on Windows 10 Home (64-bit).
NOTE: MIDI input has been disabled. It needs to be rewritten for The MidiBus library.
You can also check the file list.
|The MidiBus||MIDI input/output||themidibus.zip (132KB)|
|Minim||Audio analysis (FFT)||minim.zip (18MB)|
The text at the top of the window controls the MIDI output. The left column of 30 bars are audio meters; each meter representing an average for a frequency band produced by FFT analysis with the low frequencies at the top of the display and the high frequencies at the bottom of the display. The meters are auto-levelling and provide normalised output values between 0 and 1 (inclusive). The right column of 10 bars are meter monitors, with each one connected to a particular meter. A monitor's output value is determiend by scaling the input meter value over the monitor's output range between 0 and 127 (inclusive); the lower and upper limits of each range can be adjusted, including to scale the meter input inversely, and the meter it is connected to (thus the frequency band it monitors) can be changed. If a MIDI output device is selected, each time a monitor output value changes, the value is emitted as a MIDI control message on the selected output channel. The control number is in the range 1 to 10, with the top monitor being control 1 and the bottom one being control 10.
Click on the "SELECT OUTPUT" text to pop up the "SELECT DEVICE:" menu. Click a displayed device to select. Subsequently, clicking a displayed device name presents the "SELECT DEVICE:" menu again, and clicking the displayed channel number presents a "SELECT CHANNEL:" menu with channels 1 to 16.
Each monitor ouutputs values in the range 0 to 127 (inclusive) by default. The "minimum" and "maximum" limits can be adjusted by clicking (and dragging) the monitor output bar. Clicking in the top 3/4 of the bar adjusts the maximum; clicking in the top 1/4 of the bar adjusts the minimum. When dragging, if the mouse is dragged above or below the bar, the limit being dragged (min or max) snaps back to the previous value. Right-click the bar to reset to the default full range (0 to 127).
When the mouse is just off the left edge of a monitor bar the link to the associated meter is hilighted and "Drag to meter" is displayed. Click and drag the mouse pointer, releasing over to the desired meter; releasing when not over a meter leaves the link as it was previously. Right-clicking when "Drag to meter" is shown resets the link to the meter assigned by default when the application was started.
The "selected monitor" refers to the monitor that the mouse is over.
Note: These screenshots are from an earlier version running on Windows 7. The appearance and operation is similar in this version.